Job request as Toolpusher, Tourpusher on onshore or offshore drilling rig.

Objective To drill the wells according to drilling plan with cost effective and HSC considerations.pre planing and material availability.

*Work Experience:

1) Asst. Driller/Driller: National Drilling Company Abu Dhabi from 25 April 1981 to 10 July 1991.
2) Driller: SEDCO FOREX Drilling Company Saudia Arabia 29 July 1991 to 07 February 1997.
3) Tool Pusher/:Hamad-ul-Hamad Kuwait 25 September 1997 to 12 December 2005.
4) Tool pusher/Rig Maintainance Supervisor:Techno petroleum/ rig SAS-01 (rig been prepared ready to work for Mari Gas to work in Dehrki gas field of MGCL). 13 March 2006 till date.
Worked on :=
--Offshore jack-up Rig JUNANA(ND-7) as Driller OF National Drilling Company Abu Dhabi.
--Offshore jack-up Rig AlIthad(ND-3) as Driller OF National Drilling Company Abu Dhabi.
--Offshore jack-up Rig Hakaryou-6 as A/Driller of Japan Drilling Company Abu Dhabi.
--Onshore Rig (ND-10) as A/Driller OF National Drilling Company Abu dhabi.
--Onshore Rig (ND-1) as A/Driller OF National Drilling Company Abu dhabi.
--Onshore Rig No.7 as Driller of Arabian Drilling Company KSA(Sedco Forex).
--onshore Rig No.14 as Directional Driller of Arabian Drilling Company KSA(Sedco Forex).Worked in Hafoof, Jizan, Jeddah, Abqaiq, Hamriyah & kuwait border fields.
--Onshore Rig No.108 as Toolpusher of Hamad al Hammad Drilling, Kuwait.
--Onshore Rig No.SAS#01 as Rig Maintenence Supervisor/Toolpusher of Techno Petroleum,Pakistan.

*Education & Certificates:
1 Graduation with computer studies(AIOU Continue studies1997)
2 Intermediate in Science (CB Sir Syed Collage,1971-73,HSSC)
3 Drilling Technology course(Univer.of TEXAS,Austin ,USA 1984)
4 Secondary School Certificate(Cantt Public Sec.School!961-71)

*Certifications:
1) DRILLING TECHONOLOGY course, University of TEXAS,at Austin ,USA.
2) WELL CONTROL at rig superitendent level.
3) WELL CONTROL at supervisor level.
4) H2S certificate
5) fire fighting
6) defensive driving
7) STOP dupont
8) Well Control Course at supervisor level,Aberdeen well control institute
9) Basic Well Control at rig superintendent level, Daharan training centre
10) Rig Site Fire Fighting Course

*Additional Information:
I passed the DRILLING TECHNOLOGY Course exams from University of TEXAS at AUSTIN,USA in June 1984 in following disciples:-
a) -Managment & supervision on rig, communication, motivation, training, giving directions & orders, making good decisions.
b) -Care & maintinence of prime movers, lubrication, fuel, cooling, induction and exaust system, calculating rig horsepower, rig power designing.
c) -Electric drive rigs,AC & DC motors, generators &SCR control.
d) -Care & maintinence of derricks, Mast and substructure.
e) -Care & maintinence of drawworks, travelling assembly, swivel, crown block & rotary table.
f) -Pneumatic rig control, wire rope programmes, drillers instrument panel, data gathwering devices, duplex & triplex mud pumps.
g) -Centrifugal pumps, kelly & slips, drill string designing.
h) -Straight or controlled directional drilling, surveying.
i) -Rollercone bits, diamond bits, coring, bit programmes.
Water base muds, invert & oil base muds, solid controls.
j) -Blow out preventer and closing system.
k) -Drilling fluid hydraulics & optimized drilling, bit nozzle selection.
l) -Formation pressure control, kick control, killing well.
m) -Casing seat plan, casing designing, cementing planning & calculations, open & cased hole fishing, drill stem testing, H2S safety, well loging, well testing, running completion.