Instrument Engineer

To add value to an organization by using my knowledge and skills as Engineer and To develop my carrier with a progressive company whom can utilize effectively my potential and expertise and provide technical advancement.

Year 2007 ~ Present UTAC Singapore
Engineer

§ Responsible on the weekly pretest data monitoring and improve First pretest Yield, and fine root cause and take action to improve device problem due to contact and others Issues.
§ Responsible on the set up time target on the JTS-7000 machine to meet with production target
§ Analysis device failure on the LUL handler caused by ESD and reported to the weekly CIP meeting.
§ Responsible on the daily jam rate monitoring at JTS-7000 machine and improve some method and modified H/W to meet the target.
§ Responsible on the daily Advantest jam rate to meet with production target.
§ To come out an Idea on the improvement project to reduce set up down time any newly product by fabricate some JIG in term to reduce system down time machine, time and man.
§ Perform lot on hold verification, investigation and disposition
§ Ensure processes and procedures comply with company quality system.
§ Perform Qual buy off to all product include the machine buy off
§ Carry out relevant “On the Job” training as required
§ Liase with relevant company department, supplier and customer to communicate problems found and proposed improvement action.
§ Implementation of continuous improvements to reduce rejects and improve production / quality system efficiency.


2003 – 2007

Test Engineering

§ Responsible for the A360 Teradyne Tester, Loadboard and DUT boards Equipment
§ Responsible for the LTX-CX and LTX –DX Tester in term to maintaining and trouble shooting
§ Responsible for Synchro Fusion and PVI Tester.
§ Responsible for set up and diagnostic of tester problem
§ Establish preventive maintenance
§ Responsible for improving the Yield and optimize tester machine
§ Perform process uptime and down time Tester machine.
§ Responsible on the LTX tester, diagnostic problem, verify device problem and all issues regarding LTX tester.
§ Responsible on the Synchro QSS and Synchro PVI tester, trouble shooting and improving program to achieved OEE target
§ Carry out job training program to Line tech
§ Perform lot on hold at 9200 point, verification, investigation and disposition.

Institute TEchologies of Surabaya ( ITATS ). electrical engineering graduate

Training/Seminar Attended

§ 1997, Electrostatic Discharge Prevention, PT Siemens Components Batam.
§ 28th & 29th Sep ‘96, SIP-200 Flexiwatt Scanner and Straightener
§ 30 th June 2000, ESD Awareness Training, Infineon Technologies Batam.
§ 26th July 2001, FAILURE Mode and Effect Analysis Infineon Batam.
§ 06th Nov 1999, COACHING SKILL TRAINING, Infineon Technologies Batam.
§ 18 Oct 2001, SAFETY AWARENESS COURSE , Infineon Technologies Batam.
§ ESD seminar 2002, Globaltronic conference hall, CHANGI – SINGAPORE
§ 8th – 9th May 2003, IC product failure analysis, Infineon Singapore.
§ 28th 30th June 2004, TS16949 training course, Neville-clarke Singapore
§ 15th Jan 2005, EMS 14001 revision course, Holiday in Batam
§ Advantest Tester and handler training Singapore

Good familiar on the maintain Electronics circuit boards ( Audio / Video, TV, VCD, Power Amp Etc )
§ Working knowledge of Pneumatic and Hydraulic system for Vortex Hydra and Ressacommetta machine.
§ Good familiar to troubleshooting on Driver board / MOS driver boards.
§ Good familiar to troubleshooting on Programmable Pattern Generator
( PPG / SPPG ).
§ Good familiar to troubleshooting on Digital Linear driver boards.
§ Working knowledge in Operation and trouble shooting of :
- AEHR TEST SYSTEM 12100,12200,12000 machine.
- Remote Test system with manual and Network system.
- EPPROM Programmer.
- BTS-2000 machine.
- ALS-1000 machine Loader / Unloader machine.
- BTH and SIP machine.
- DESPATCH Bake- In Oven VCR2-Series
- Heraeus Bake-in Oven.
- HORA Profet Machine.
- Super Dry M/C
- A360 Teradyne machine
- LTX CX and DX Tester
- Synchro PVI and Fusion
- OS handler
- JTS-7000 pick and place
- Advantest handler
- Advantest tester