process engineer

ľ Basic Design of petroleum Refinery & field Equipments such as: Heat Exchangers, Condensers, water coolers, Air cooler, Pressure vessels, two & three phase separators, etc.

Basic Design of petroleum Refinery & field Equipments such as: Heat Exchangers, Condensers, water coolers, Air cooler, Pressure vessels, two & three phase separators,etc.
Selection and Layout the technical specification of safety valves.
Design and lay out the pump system
Design of Process flow diagrams.(PFD)and (P&ID)
Preparation of process data sheets for equipment
Preparing HAZOP study
Following up of operation of atmospheric Distillation Units.
Following up of operation of UOP stabilized gasoline hydro-treating and Isomerization unit.
Following up of operation of water treatment unit.
Review third party process design work.
Familiar with operation of DCS
Review isometric drawings
2002 Participation in preparing of database of equipment in our company CORC
2002 following up a drying of a main heater in distillation unit in CORC
2003 Participation in design of VRU unit for COR, and I had the work of design of condenser and heat exchanger
2003 sizing a flare stack for AMRIA PETROLEUM CO. (Amria, Alexandria)
2004 Participation in a design of three phase separator for QARUN Petroleum Co.
(Sizing the vessel, sizing safety valve, design P&ID, and preparing technical data sheets)
2004, 2005, 2006, 2007 Participation in a design of a new production facilities plant for ESH El- MALAHA Petroleum Co. (Hurgada). The plant including production separator, test separator, closed drain and knock out drum. (Sizing the knock out drum, participated in sizing separators, participated in design of P&ID, and preparing the plant technical manual)
2005 Participation in a design of three phase separator for GISUEM Petroleum Co.
2005 Participation in gasoline storage tanks piping network design for COR
(Sizing gasoline pipelines)
2006 Participation in a design of three phase separator for ALAMIN Petroleum Co (Sizing the separator and its internals, specifying its safety valve, sizing nozzles, preparing data sheet adjust control points and design of P&ID
2007 design of P&ID of pre-flash tower in CORC
2007 Participation in design of H. Naphtha treating unit CORC, (Specifying its safety valves and design of P&ID.)
2008 Design of three phase separator for ALAMIN Petroleum Co, (Sizing the separator and its internals, specifying its safety valve, sizing nozzles, preparing data sheet adjust control points and design of P&ID

B.SC in petroleum refining & chemical engineering
From Suez Canal university, faculty of petroleum & mining engineering (Suez-Egypt) May 1998.

EXPERIENCE:
2008 Sizing crude oil transfer line from ESH El- MALAHA co. to SUCO co.
2008 design of a special unit to provide LPG under constant pressure of 10 bar for MISR HEGAZ co. (basic design, design of P&ID, reviewing manufacturing, and preparing commissioning steps)
(Sizing the vessel, sizing safety valve, design P&ID, and preparing technical data sheets)
2008 design of flare ignition system (PETROBEL).
Daily work of following up performance and rating of equipment (towers , heat exchangers networks) in the company and studying any problems in operations and participate in the solution of these problems CORC
Monthly Review chemicals injection which improving operations CORC
Work as instructor in pipelines sizing courses (CORC)
Work as instructor in a heat-exchanger design courses (GLOBAL Co.)
Have studies in natural gas sweetening and dehydration
Searches in low NOx burners
Searches in fare gas recovery.
REFERENCES OF WORK:
-Sizing and specifying of safety valves according to API 520,521,526.
-Sizing of flare stack according to API 521
-Sizing of separators according NATCO papers and API
-Rating of distillation towers by PROII and HYSYS
-Rating and design of heat-exchangers by PROII, HEXTRAIN according to TEMA
-Sizing pipelines by PROII , INPLANT or VISUAL FLOW
SIMULATION PACKAGE:
¡VHYSYS 3.2
¡VPRO II (8)
¡VHEXTRAIN (9.1)
¡VVISUAL FLOW (5.2)
¡VINPLANT (3.2)