work in instrumentation and automation (Instrument devices, PLC and controllers)

instrumentation and automation engineer

Sugar Cane &By Product Development Company Mar 2004 – Present
•Responsible for instrument maintenance and developing in the Mill House in Salman Farsi sub-company and the use of hardware (Telemecanique Micro and Premium PLCs)and software (Telemecanique PLCs Junior V4.2) in the Mill House
•Experience in working with different kinds of Instrument equipments in the Mill House with Skoda Co. in the Salman Farsi sub–company in installation and commissioning
•Research about protection developing in the Mill House for turbines and conveyers by using Telemecanique XBTN hardware(HMI) and XBTL1000 V4.42 design software via communication with Telemecanique PLC
•Experience in working with different kinds of Instrument equipments in the Raw House with SIIC Co.(Egyptians Co.) in the Salman Farsi sub–company in installation and commissioning
•Experience in working with Siemens PLC hardware(S7-400,Teleperm M) and software( Prograph AS+) in the Raw House
•Experience in working with Siemens PLC (hardware & software) S7-300 and WINCC in Water treatment
•Responsible for instrument maintenance in the Power House in the Salman Farsi sub-company and the use of hardware and software Telemecanique PLCs Junior V4.2 , Siemens PLCs S7-200 in the Power House
•Research, and adjust control loop project for imbibition in the Mill House (control water flow and its temperature according to weighing amount of bagasse in moving conveyer via two hot & cold control valves automatically by ABB controller – Digitric 500 and Schenck scale)
•Research and adjust control loop project for Donely Shoot (control amount of cane before compressing via changing turbine turn by Endress + Hauser sensor, transmitter, and ABB controller-Digitric 500) in the Mill House
Note: This two projects was very important because have big effect in factory efficiency(almost have 4000$ daily efficiency)
Pishgam Gostare Daghigh Sanat Co. Mar.2007-Present
•Programming Omron PLC (CPM2A-40CDR) with CX-Programmer for motor protection in water pumping station for khuzestan waste water Department
•Maintenance different electronics boards for Kuzestan Power Organization
•Service and calibration industrial devices for Kuzestan Power Organization

Bachelor of Science (Sep.1996 – Feb 2002)
Electrical and Computer Engineering,
Dept. of Electrical and Computer Eng., Isfahan University of Technology, Isfahan, Iran
Project Title: “Trouble Shooting of Combinational CMOS – ICs via Parallel Port”, Sept 2001
Advisor: Farid Shaikh Al-aslam, PhD

Process of sugar product : Kosha Company,
Pneumatic (Primary): Festo Company,
PLC-S5 (Primary): Contronic Company,
Instrument in Oil Refinery (Instrument, Analyzer, workshop, primary in DCS): Shazand Arak Oil Refinery,
PLC-S7 (primary): Contronic Company,
PLC-S7 (Advanced): Contronic Company,
WinCC (PLC Siemens Monitoring): Contronic CompanyTelemecanique PLC (Hardware and Software): Power Station, Salman Farsi Sugar Company
PLC-PCS7 (Primary and Advanced): Foolad Technic Co.
Fundamental of Safety: Kuzestan Power and Water Industry Institute
IMS(Integrated Management System)-TQT Company:Salman Farsi Sugar co.
Fundamentals & Concepts of Calibration:Deghat Gostar Engineering
Weighing in Dynamic Conveyers
Industrial Networks – Profibus
PLC-TWIDO & HMI-XBTN: Schneider Electric

Experience in working with instrument devices and controllers in industrial environments
Experience in working with Telemecanique & Siemens &Omron PLC,s (Hardware & Software)
Experience in teaching labs to electrical engineering students in the university
Individual with interpersonal skills in teamwork
Enjoy dynamic and challenging work environments
Interest to researching and working on control and automation subjects
Technical and communication skills capabilities
Language:
•English: Good
•Arabic : Fluent