QA/QC Engineer

Seeking a position as QA/QC Mechanical Engineer in the field of Engineering in a company where my potentials and my acquired knowledge can be utilized at optimum level and I can make meaningful contribution and grow professionally.

„Ï Work as Mechanical Inspector client representative responsible for all quality concerns relative to mechanical activities in my package of jurisdictions such as welding, piping, storage tank construction, Construction of Sphere pressure Vessel, Construction of Spheroid Low Pressure Storage tank, API Pumps Installation ensure the compliance with the project specification, standards & codes. Maintain a look-ahead schedule of proposed Expenditure Requests in order to facilitate the planning for inspection manpower, requirements based on Project Quality Plans and Schedule ¡§Q¡¨ of attachment VI.Assist PMT in enforcing and interpreting Company standards codes and specifications, and recommend solutions to construction problems/ violations and if possible consult with the assigned Specialist in the Engineering Services Organization.Review & Approved the Contractor's quality control documents and test results for conformance to project requirements such as Inspection Test Plan (ITP), Procedures, and Method Statement and submittal of special process based on Schedule ¡§Q¡¨ requirement. Conduct interview of Contractor's proposed QC personnel & disqualified any individual if found unsatisfactory performance. Initiate weekly quality meeting with the contractor to discuss quality highlights such as Log Book Entry, Proactive Notifications, General Comment, Standard Violation, NCR to ensure that such problems does not happen again. Liaise with the PMT regarding corrective actions against NCR.
Ensure that all welding procedure is approved and welders are qualified.Conduct site surveillance of welding activities before, during and after welding basis to ensure that they follow the WPS and related standards. Perform inspection on cylindrical tank with, floating roof, dome roof, internal floating roof, spheroid low pressure storage tank, spherical pressure vessel, check the foundation level, tank bottom plates laying inspection, material traceability.Perform inspection of tank shell plates erection, fit up of vertical & horizontal joint, nozzles orientation, stair & structural related to tank, Bottom test(vacuum box test), oil penetrate test(OPT) Pneumatic test of nozzles pad, Plumbness( verticality), peaking, banding, roundness, hydro test, Hydro pneumatic test inspection.Review of Tank & Piping Hydro Test Package & NDT requirement according to codes
„Ï

Bachelor of Science in Mechanical Engineering
Technological Institute of the Philippines, Manila, Philippines
Graduated on : April 12, 2004
Passed Licensure Exam on: October 2004
PRC Registration #: 0064193


Secondary Education
Isabela National High School
# 132 Claraval St., San Vicente, Ilagan, Isabela
(1996 - 1999)


Primary Education
Bigao, Elementary, School
Brgy.Bigao, Ilagan, Isabela
(1989 - 1996)

ISO-9001-2008 Quality Management System Auditor/Lead Auditor NevilleClarke
CSWIP 3.1 Welding Inspector TWI

Comprehensive Training Program for Oil and Gas Drilling Basic Introduction for Drilling Technology
Introduction to Hydrogen Sulphide H2S RODECH

IADC Rig Pass Orientation & Basic Safety Awareness RODECH

First Aid at Oil & Gas Drilling Rig RODECH

Basic Occupational Safety and Health for Construction RODECH

Position: Mechanical Inspector (Client Representative)
Professional Qualification: Licensed Mechanical Engineer
Licensed Number: 0064193
Years of Work Experience: 8 years
Geographical Areas of Work: Philippines, Saudi Arabia & Qatar
CSWIP 3.1 Cert. #: 55037
ISO 9001-2008 QMS Cert. # PP-QMS03-2692
Saudi Aramco Personal (SAP) #: 70009451
Qatar Petroleum: Piping/Welding Inspector Approved
International Codes Standard Used: ASME B31.1 / B31.3, ASME Sec. V, VIII Div.2, IX, API 1104,
API 650, API 620, API 610, AWS D1.1 ISO Standard, BS Standard, Aramco & QP Standard