| Reference | BID7849 |
| Date | 5/6/2004 |
| Location | Middle East |
| Scope | Ref. No.: 96-08-3802 Issue Date: 6/5/2009 Bid Closing Date: 1/6/2009 Fee: 600 USD Bid Bond: 1% From the total value of tender price Offer Validity: 120 days from the Bid Closing Date Bond Validity: 90 days from the Bid Closing Date Scope of Work: South Oil Company (SOC) proposed to have crude oil pumping station for operation purposes. The crude oil will be pumped from flow tank to PS-2 station at 47 km distance in 16" trunk line. The station to be comprise three (3) electrical driven vertical booster oil pumps ASSY.C/W electrical motor local starter, and control panel, suction and dis. valve, strainer, check valve, and (3 nos) electrical driven main pumps horizontal centrifugal oil. Pump assy. C/W electrical motor local starter, and control panel suction and dis. valve (M.O.V) instrument gauges and all accessories on skid. Interconnecting piping fitting valves, strainer and all accessories as requirements. 1- Supply of # 3 booster oil pump (ACC. API 610 latest addition) - Operating condition: API gravity: 23-27 Capacity: 100 m3/hr Npsh: 6 m Discharge pressure: 7 kg / cm2 Sulphur content wt %: 3.72 Kinematics viscosity SCT @ 21°c: 29.5-51.8 Amb. Temperature: 0°c-55°c - Contracting and materials: Double-casing diffuser vertically ACC. API (610-8) Casing: carbon steel Impeller: API (610-8) S. steel Shift: API (610-8) S. steel Suction nozzle: ANSI 300 # rf Discharge nozzle: ANSI 300# rf Type of seal: mechanical .flow serve equivalent - Case wearing ring: S. steel Shaft sleeve: S. steel Pump efficiency: as high as possible Type of coupling: flexible coupling (meta stream) - Electric motor specifications: Voltage: 380 v, 3 ph Rated power: 10% greater than mechanical absorbed Frequency: 50 hz Insulation class: f Duty: continuous Ingress protection: ip 55/EEX-DIIBT4 Complete with operating panel (with space heater), push button Station out door use EEXDIIBT4 type contains of selector switch (auto off-man) with: 1 no. start, 1 no. stop, 1 no. ammeter with states lamps (run-stop-ready to start) 2- Supply of # 3 electrical main pump (ACC. API 610 latest addition) - Operating condition: API gravity: 23-27 Capacity: 100 m3/hr Suction pressure: from booster pump Discharge pressure: (40 min.-50 max.) kg / cm2 Sulfur content wt %: 3.72 Kinematics viscosity SCT @ 21°c: 29.5-51.8 Amb. Temperature: 0°c-55°c Contracting and materials: Horizontal centrifugal TI API (610-8) last addition Casing: carbon steel Impeller: API (610-8) S. steel Shift: API (610-8) s. steel Suction nozzle: ANSI 600# rf Discharge nozzle: ANSI 600# rf Type of seal: mechanical flow serve equivalent Case wearing ring: S. steel Shaft sleeve: S. steel Pump efficiency: as high as possible Type of coupling: flexible coupling (Meta stream) Type of casing: axially split NO. of stages: no more than (6 staged) Electric motor specifications: Voltage: 11 kv, 3 ph Frequency: 50 hz Rated power: 10% greater than mechanical absorbed power Insulation class: f Duty: continuous Ingress protection: ip 55/ EXX-DIIBT4 Complete with push button station out door use EEX-DIIBT4 type contains of selector switch (auto-man) with: 1 no. start, 1 no. stop, 1 no. ammeter with states lamps (run-stop-ready to start) Instrumentation: Complete instrumentation packages should be included within the material of supply. The instruments should include: 1- All local instruments including protection sensor (vibration proof and high temperature winding) and gauges. 2- Local control and operating panel for each pump separately. 3- Common control remote panel with MINIC to be installed inside the control room to control and operate each pump individually. 4- All required control cables to be connected between local site equipments and remote control panel inside the control room not less than 500 mtr. Origins are: West European, USA, Japan. |
