| Reference | SDG4161P20/07 |
| Date | 3/31/2020 |
| Location | Asia |
| Scope | The company announces its need for Supply of Hand Slip. - Item 001, QTY=4 of Hand Slip for 4.1/2 Inches OD Drill Pipe. A. Each Rotary hand slip should be manufactured and monogrammed strictly as per API 7K (latest edition). Each Rotary hand slip should consist of, but not limited to: 1) Rotary hand slip 127.00 mm (5 inches) Body complete with Elastomer Flex handles & inserts for 114.30 mm (4.1/2 inches) OD drill pipe. Hand slip should have an API taper of 4 inch/ft. & suitable for use in 27.1/2 inches Square drive Rotary Table. 2) Minimum Load bearing capacity of the Rotary Hand Slip should be not less than 350 Ton. 3) The supporting slips should have minimum 13.3/4 inches (349.25 mm) gripping length. 4) The slips should be manufactured from high quality alloy steel; fully heat treated and should strictly conform to API 7K (latest edition). 5) Mass Slip weight i.e. weight of the complete slip with inserts and handles should be within 200 pounds (Maximum) 6) Extra set of Inserts for each slip - 2 Set (Total 8 Sets). 7) Extra Elastomer Flex Handle for each slip - 2 Numbers (Total 8 Nos). B. SPECIAL REQUIREMENTS: 1) SR-1 Proof Load Test: The items (HAND SLIP FOR 4.1/2 INCHES OD DRILL PIPE) shall be given a proof load test and subsequently examined in accordance with 8.6 and should be marked "SR-1" accordingly near the load rating identification (API Specification 7K – Annex A.2). Test reports should be submitted along with the supply. 2) SR-3 Data Book: The Manufacturer’s Data Book as per API Specification 7K – Annex A.5 for all of the items should be submitted along with the supply. -Item 002,QTY=6 of Hand Slip for 5 Inches OD Drill Pipe. A.Each Rotary hand slip should be manufactured and monogrammed strictly as per API 7K (latest edition). Each Rotary hand slip should consist of, but not limited to: 1) Rotary hand slip 127.00 mm (5 inches) Body complete with Elastomer Flex handles & inserts for 127.00 mm (5 inches) OD drill pipe. Hand slip should have an API taper of 4 inch/ft. & suitable for use in 27.1/2 inches Square drive Rotary Table. 2) Minimum Load bearing capacity of the Rotary Hand Slip should be not less than 350 Ton. 3) The supporting slips should have minimum 13.3/4 inches (349.25 mm) gripping length. 4) The slips should be manufactured from high quality alloy steel; fully heat treated and should strictly conform to API 7K (latest edition). 5) Mass Slip weight i.e. weight of the complete slip with inserts and handles should be within 200 pounds (Maximum) 6) Extra set of Inserts for each slip - 2 Set (Total 12 Sets). 7) Extra Elastomer Flex Handle for each slip - 2 Numbers (Total 12 Nos). B. SPECIAL REQUIREMENTS: 1) SR-1 Proof Load Test: The items (HAND SLIP FOR 5 INCHES OD DRILL PIPE) shall be given a proof load test and subsequently examined in accordance with 8.6 and should be marked "SR-1" accordingly near the load rating identification (API Specification 7K –Annex A.2). Test reports should be submitted along with the supply. 2) SR-3 Data Book: The Manufacturer’s Data Book as per API Specification 7K – Annex A.5 for all of the items should be submitted along with the supply. -Item 003, QTY=6 of Hand Slip for 13.3/8 Inches OD Drill Pipe. A.Each Rotary hand slip should be manufactured and monogrammed strictly as per API 7K (latest edition). Each Rotary hand slip should consist of, but not limited to: 1) Extra long Casing hand slips complete with handles & circular buttons for 339.725 mm (13.3/8 inches) OD casing pipes. Hand slip should have an API taper of 4 inch/ft. 2) Extra set of circular buttons for each slip - 1 set (Total 06 sets) 3) Minimum load bearing capacity of the casing slips should not be less than 450 Tons. 4) The supporting slips should have minimum 13 inches (330.20 mm) gripping length and should provide maximum circumferential grip for uniform pressure around the casing. 5) The handles should be flexible type and centre handle to be provided for better handling of the equipment. B. SPECIAL REQUIREMENTS: 1) SR-1 Proof Load Test: The items (HAND SLIP FOR 13.3/8 INCHES OD CASING) shall be given a proof load test and subsequently examined in accordance with 8.6 and should be marked "SR-1" accordingly near the load rating identification (API Specification 7K – Annex A.2). Test reports should be submitted along with the supply. 2) SR-3 Data Book: The Manufacturer’s Data Book as per API Specification 7K – Annex A.5 for all of the items should be submitted along with the supply. - Item 004, QTY=7 of Hand Slip for 9.5/8 Inches OD Drill Pipe. A.Each Rotary hand slip should be manufactured and monogrammed strictly as per API 7K (latest edition). Each Rotary hand slip should consist of, but not limited to: 1) Extra long Casing hand slips complete with handles & circular buttons for 244.475 mm (9.5/8 inches) OD casing pipes. Hand slip should have an API taper of 4 inch/ft. 2) Extra set of circular buttons for each slip - 1 set (Total 07 sets) 3) Minimum load bearing capacity of the casing slips should not be less than 450 Tons. 4) The supporting slips should have minimum 13 inches (330.20 mm) gripping length and should provide maximum circumferential grip for uniform pressure around the casing. 5) The handles should be flexible type and centre handle to be provided for better handling of the equipment. B. SPECIAL REQUIREMENTS: 1) SR-1 Proof Load Test: The items (HAND SLIP FOR 9.5/8 INCHES OD CASING) shall be given a proof load test and subsequently examined in accordance with 8.6 and should be marked "SR-1" accordingly near the load rating identification (API Specification 7K – Annex A.2). Test reports should be submitted along with the supply. 2) SR-3 Data Book: The Manufacturer’s Data Book as per API Specification 7K – Annex A.5 for all of the items should be submitted along with the supply. -Item 005, QTY= 4 of Hand Slip for 7 Inches OD Casing. A.Each Rotary hand slip should be manufactured and monogrammed strictly as per API 7K (latest edition). Each Rotary hand slip should consist of, but not limited to: 1) Extra long Casing hand slips complete with handles & circular buttons for 177.80 mm (7 inches) OD casing pipes. Hand slip should have an API taper of 4 inch/ft. 2) Extra set of circular buttons for each slip - 1 set (Total 04 sets) 3) Minimum load bearing capacity of the casing slips should not be less than 350 Tons. 4) The supporting slips should have minimum 13 inches (330.20 mm) gripping length and should provide maximum circumferential grip for uniform pressure around the casing. 5) The handles should be flexible type and centre handle to be provided for better handling of the equipment. B. SPECIAL REQUIREMENTS: 1) SR-1 Proof Load Test: The items (HAND SLIP FOR 7 INCHES OD CASING) shall be given a proof load test and subsequently examined in accordance with 8.6 and should be marked "SR-1" accordingly near the load rating identification (API Specification 7K – Annex A.2). Test reports should be submitted along with the supply. 2) SR-3 Data Book: The Manufacturer’s Data Book as per API Specification 7K – Annex A.5 for all of the items should be submitted along with the supply. -Item 006, QTY= 6 of Hand Slip for 3.1/2 Inches OD Drill Pipe. Each Rotary hand slip should be manufactured and monogrammed strictly as per API 7K (latest edition). Each Rotary hand slip should consist of, but not limited to: 1) Rotary hand slip 114.30 mm (4.1/2 inches) Body complete with Elastomer Flex handles & inserts for 88.90 mm (3.1/2 inches) OD drill pipe. Hand slip should have an API taper of 4 inch/ft. & suitable for use in 27.1/2 inches Square drive Rotary Table. 2) Minimum Load bearing capacity of the Rotary Hand Slip should be not less than 350 Ton. 3) The supporting slips should have minimum 13.3/4 inches (349.25 mm) gripping length. 4) The slips should be manufactured from high quality alloy steel; fully heat treated and should strictly conform to API 7K (latest edition). 5) Mass Slip weight i.e. weight of the complete slip with inserts and handles should be within 210 pounds (Maximum) 6) Extra set of Inserts for each slip - 2 Set (Total 12 Sets). 7) Extra Elastomer Flex Handle for each slip - 2 Numbers (Total 12 Nos). B. SPECIAL REQUIREMENTS: 1) SR-1 Proof Load Test: The items (HAND SLIP FOR 3.1/2 INCHES OD DRILL PIPE) shall be given a proof load test and subsequently examined in accordance with 8.6 and should be marked "SR-1" accordingly near the load rating identification (API Specification 7K – Annex A.2). Test reports should be submitted along with the supply. 2) SR-3 Data Book: The Manufacturer’s Data Book as per API Specification 7K – Annex A.5 for all of the items should be submitted along with the supply. |
| Bid Bond | INR 3,11,800.00 |
| Offer Validity | 120 days |
